Oki All in One Printer ES3640 MFP User Manual

ES3640e MFP Software Installation Guide  
®
Windows TCP/IP Network Installation.....2  
About this Guide  
Novell Installation ......................................7  
This guide describes the initial printer driver  
®
installation. For more detailed information, refer to  
the EFI User Software Installation Guide and EFI  
Configuration Guide provided on the User  
Documentation CD (CD3).  
Macintosh Installation..............................8  
OS 9.1 to 9.2.x.......................................8  
OS X.1+ to X.3+................................... 10  
The general steps for installing the software are as  
follows:  
• Install the PostScript or PCL printer driver and  
corresponding printer driver files.  
• Set up the printer driver to communicate with  
the Fiery.  
• Install Fiery utilities and user software.  
• Configure Fiery utilities and user software.  
You must also configure either a local connection  
for printing directly to your printer or a network  
connection for printing over a network.  
NOTE  
A full set of user documentation, where  
procedures are described in detail, is provided on  
the User Documentation CD (CD3).  
Service and Support  
• Consult the dealer where you purchased your  
system.  
• Visit our web site: http://my.okidata.com  
1
 
Windows TCP/IP  
Network Installation (cont’d)  
14. Select Yes and press ENTER to Save Changes.  
1 Assign an IP address to the MFP  
Press ENTER to Exit the Setup Menu.  
If you are not using DHCP, you need to obtain an IP  
Address from your network Administrator and  
enter it using the front panel:  
15. Printer restarts the server and initializes. Ready  
to Print displays.  
1. Confirm that the printer displays [Ready to  
print].  
2. Press key until [Admin Setup] appears. Press  
ENTER.  
3. Continue to Setup? displays. Press ENTER to  
select Yes. The printer goes offline and Running  
Setup displays. This will take about a minute.  
4. The Setup Menu displays, press to select  
Network Setup. Press ENTER.  
5. Press to select Protocol Setup. Press ENTER.  
6. Press to select TCP/IP Setup. Press ENTER.  
7. Press to select Ethernet Setup. Press ENTER.  
8. TCP/IP Ethernet displays. Select Yes and press  
ENTER. Enable AutoIP Config? displays. Select No.  
Press ENTER.  
9. The default IP Address displays. Use or to  
change each octet. Press ENTER to proceed to  
the next octet or to leave the octet unchanged.  
10. Subnet Mask displays. Repeat instructions in  
step 9.  
11. TCP/IP bound to Ethernet displays. Press ENTER.  
12. Gateway Address displays. Repeat instructions in  
step 9.  
13. Press ENTER to exit TCP/IP Setup, Protocol  
Setup, and Network Setup.  
3
 
Windows TCP/IP  
Network Installation (cont’d)  
2 Install the Fiery PostScript Printer  
Driver  
NOTE  
In order to send documents to the MFP, the LPR  
utility must be installed. LPR installs  
1. Insert the printer driver CD (CD1) into your  
CD-ROM drive. The CD will autorun.  
automatically when the drivers are installed  
using the Menu Installer as instructed here. If  
drivers are installed using Windows Add Printer  
Wizard, you must manually load the LPR Utility  
from the Menu Installer on CD1. To do this, click  
Custom Install /Network Software/  
If it doesn’t autorun, click Start Run →  
Browse. Browse to your CD-ROM drive.  
Double-click Install.exe. Click OK.  
2. Select your language.  
InstallationConfig/OKI LPR.  
3. Click Next to accept the License Agreement.  
4. Select Custom Install to install the printer  
3 Install Printer Utilities  
driver and the software utilities.  
To install only the printer driver, select  
Minimal Install and skip the next step.  
Select Custom Install in the Menu Installer on the  
driver CD (CD1). Choose from these software  
tools:  
5. Click the Printer Driver Installer button.  
Network Software  
6. Select Network Printer. Click Next.  
Click Installation/Config to select utilities for  
network printing, installation, and  
configuration.  
7. Select Directly to the Network using TCP/  
IP.  
8. The TCP/IP Connection screen displays. Select  
Click Administration Tools to select network  
management tools.  
Search Address. Click Next.  
9. Highlight your printer model. Click Next.  
Productivity Software  
10. Select Printer Emulation. Click Next.  
Select Windows printer software.  
11. Follow the on-screen instructions to complete  
the installation.  
Follow the on-screen instructions to install the  
utilities.  
Discover the MFP  
The LPR Utility is automatically installed with the  
network printer driver. To discover the printer, do  
the following:  
1. Click Start Programs Oki  
Data Oki Data LPR Utility.  
2. Click Remote Print. Then, click Add Printer.  
3. Select your printer model from the drop-down  
list, then either enter the IP Address manually,  
or click Discover and wait for the printer to be  
discovered. Click OK.  
4
 
Windows TCP/IP  
Network Installation (cont’d)  
4 Install the EFI Fiery Utilities  
5 Activating Options  
1. Insert the EFI Utilities CD (CD2) into your  
CD-ROM drive.  
After you have completed the printer driver  
installation, you must configure the MFP for the  
installed options. You can configure the options  
manually or, for TCP/IP network connections, you  
can use the Two-Way Communication feature to  
configure the options automatically.  
2. Select your language.  
3. Click Next to accept the License Agreement.  
4. Select your printer model. Click Next.  
To Configure Options Manually  
1. Click Start Settings Printers.  
5. Select Quick Install to install only Command  
WorkStation, or, select Custom Install to  
install your choice of these EFI tools:  
2. Right-click the OKI ES3640e MFP EFI Fiery  
icon.  
> Command WorkStation  
> Fiery Mail Port  
3. Click Properties.  
4. Click the Installable Options tab.  
> Fiery Printer Delete  
> Fiery Downloader  
> Fiery ColorWise Pro Tools  
> Fiery Remote Scan  
NOTE  
In PCL emulation, click the Device Options tab  
and specify the options installed on your  
printer.  
If the computer will not be used by an ES3640e  
MFP administrator, Command WorkStation may  
not be required.  
5. Select an installed option from the Available  
Options list.  
6. Click Add to move the option to the Installed  
Options list.  
7. Click Apply. Click OK.  
To Configure Options Automatically  
If you have a TCP/IP-enabled network, you can  
automatically update your printer driver to reflect  
the options currently installed on the printer.  
1. Click Start Settings Printers.  
2. Right-click the OKI ES3640e MFP EFI Fiery  
icon.  
5
 
Windows TCP/IP  
Network Installation (cont’d)  
3. Click Properties.  
6 Install the User Documentation  
4. Click the Installable Options tab.  
5. Select Two-Way Communications.  
1. Insert the User Documentation CD (CD3) into  
your CD-ROM drive. The CD will autorun.  
If it doesn’t, click Start Run Browse.  
Browse to your CD-ROM drive. Double-click  
Install.exe. Click OK.  
2. Follow the on-screen instructions.  
6. Type the Fiery IP address or DNS name.  
7. To display the printer’s current default settings  
when opened, select Update Fiery Driver  
When Opened.  
8. Click Update. Click OK.  
6
 
Windows Network Installation  
Novell  
1 Install the Utility  
2 Install the MFP on a Novell® Network  
This utility installs, configures, and manages Oki  
network print server devices.  
Novell Client for Windows must be loaded, the  
Admin Manager software must be running, and  
you must be logged in to NDS.  
1. Insert the printer driver CD (CD1) into your  
CD-ROM drive. The CD will autorun.  
1. Run Discover.  
If it doesn’t autorun, click Start Run →  
Browse. Browse to your CD-ROM drive.  
Double-click Install.exe. Click OK.  
2. Select Setup from the menu.  
3. Click Create a NetWare Queue.  
4. Select NDS Mode. Click Next.  
5. Select the container. Click Next.  
6. Select Print Server Mode. Click Next.  
7. Select or create a queue. Click Execute.  
2. Select your language.  
3. The Licence Agreement appears. Click Next to  
accept.  
4. Select Custom Install.  
5. The Menu Installer screen appears.  
6. Click the Network Software button.  
7. Click the Installation/Config button.  
8. Click the Admin Mgr/Quick Setup button.  
Launching the Utility  
To launch the utility click  
Start Programs Oki Data Setup  
Utility Admin Manager.  
9. Setup Assistant displays. Select your  
language.  
3 Activating Options  
10. Follow the on-screen instructions to complete  
the installation.  
If your MFP has optional paper trays or a finisher  
installed, they must be activated in the printer  
driver. See page 5 for instructions on how to do  
this.  
NOTE: You can either install the software while  
running the utility off the CD, or you can choose  
to install the utility on your computer and then  
launch it from there.  
NOTE  
For more information, see the Configuration  
Guide on the User Documentation CD.  
7
 
®
Macintosh Installation  
OS 9.1 to 9.2.x  
2. Select the LaserWriter8 icon and highlight the  
1 Install the Driver  
printer name (print server ID#).  
1. Turn the MFP ON, then turn the computer ON.  
3. Click Create.  
2. Insert the printer driver CD (CD1) into your  
CD-ROM drive.  
4. Select OKI ES3640e MFP PPD. Click Select.  
5. Close Chooser.  
3. Double-click the OKI CD icon that appears on  
the desktop.  
4. Double-click the MAC icon.  
3 Create the Desktop Printer for USB  
5. Double-click Installer for MAC OS 9.  
6. Double-click Mac Installer ES3640e MFP.  
7. Click Continue.  
1. Navigate to Applications Mac OS 9  
Utilities.  
2. Double-click the Desktop Printer Utility icon.  
3. In the drop-down box, select LaserWriter 8.  
8. If prompted, select your language.  
4. Highlight Printer (USB) under Create  
9. The License Agreement appears. Click Accept  
Desktop. Click OK.  
to accept the terms.  
5. Under USB Printer Selection, click Change.  
10. Click Easy Install to install PPD Files, Adobe  
PS Package, and Printing Plug-ins.  
6. Highlight your MFP model. Click OK.  
Click Custom Install to install your choice of  
Adobe PS Package, PPD Files, Adobe PS  
Options Plug-ins, SDM for MAC, Swatch Utility,  
Admin Setup Utility, Printing Plug-ins.  
7. Click Create. The MFP icon appears on the  
desktop.  
8. Click AutoSetup.  
11. Click Continue to install additional utilities.  
12. When the installation is complete, click Quit.  
2 Create the Desktop Printer for a  
Network  
1. Activate Chooser from the Apple menu.  
8
 
®
Macintosh Installation  
OS 9.1 to 9.2.x (cont’d)  
4 Install the EFI Fiery Utilities  
5 Install the User Documentation  
1. Place EFI Utilities CD (CD2) in the CD-ROM  
drive.  
For additional information on using MFP features as  
well as MFP utilities, see the on-line  
documentation.  
2. Double-click the OKI CD icon that appears on  
Requirements  
the desktop.  
• Microsoft Internet Explorer version 4.0 or higher  
and Acrobat Reader.  
3. Double-click the MAC icon.  
To Load  
4. Double-click User Software.  
In order to open the on-line documentation, you  
must have Acrobat Reader installed.  
5. Double-click the OS X icon to install Command  
Workstation LF.  
1. Insert the User Documentation CD (CD3) into  
your CD-ROM drive.  
6. Double-click Mac Color Files to install CMYK  
Color Reference, Pantone Book, RGB Page 1,  
RGB Page 2, and Calibration utilities.  
2. From the CD contents folder, drag the Manual  
folder to the desktop.  
7. Double-click Color Sync to install ICC files.  
8. Follow the on-screen instructions.  
9
 
®
Macintosh Installation  
OS X.1+ to X.3+  
1 Install the Driver and Utilities  
3 Install the EFI Fiery Utilities  
1. Turn the MFP ON, then turn the computer ON.  
1. Place CD2 in the CD-ROM drive.  
2. Place the CD supplied with the MFP in the  
CD-ROM drive.  
2. Double-click the OKI CD icon that appears on  
the desktop.  
3. Double-click the OKI CD icon that appears on  
the desktop.  
3. Double-click the MAC icon.  
4. Double-click User Software.  
4. Double-click the MAC icon.  
5. Double-click the OS X icon to install Command  
5. Double-click the MAC OS X icon.  
6. Double-click Installer for MAC OS X.  
7. If prompted, select your language.  
Workstation LF.  
6. Double-click Mac Color Files to install CMYK  
Color Reference, Pantone Book, RGB Page 1,  
RGB Page 2, and Calibration utilities.  
8. License Agreement appears. Click Accept to  
7. Double-click Color Sync to install ICC files.  
accept the terms.  
Follow the on-screen instructions.  
9. Click the Install button.  
10. Click Quit.  
2 Adding the MFP  
1. Run the Print Center (or Print Setup Utility X.3).  
Click Add printer.  
2. Select IP Printing from the drop down menu.  
NOTE: If you are using USB, select USB and  
disregard the following step.  
3. Enter the MFP's IP address.  
4. From the Printer Model drop down menu, select  
the correct PPD for your printer model. Click  
Add.  
5. Quit the Print Center.  
In order to use the IP Printing connection, the  
user may need to enter the Queue name as  
“Direct, Print, or “Hold” instead of the default  
blank.  
10  
 
®
Macintosh Installation  
OS X.1+ to X.3+ (cont’d)  
4 Install the User Documentation  
For additional information on using MFP features as  
well as MFP utilities, see the on-line  
documentation.  
Requirements  
• Microsoft Internet Explorer version 4.0 or higher  
and Acrobat Reader.  
To Load  
In order to open the on-line documentation, you  
must have Acrobat Reader installed.  
1. Insert the User Documentation CD (CD3) into  
your CD-ROM drive.  
2. From the CD contents folder, drag the Manual  
folder to the desktop.  
11  
 
Trademarks  
OKI is a registered trademark of Oki Electric Industry Company, Ltd.  
Microsoft, Internet Explorer and Windows are either registered trademarks  
or trademarks of Microsoft Corporation in the United States and other countries.  
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation.  
Apple, Macintosh, Mac and Mac OS are registered trademarks of Apple Computer.  
Other product names and brand names are registered trademarks or trademarks of their proprietors.  
Command WorkStation, EFI, Fiery, the Fiery logo are registered trademarks of Electronics for Imaging, Inc.,  
in the U.S. Patent and Trademark Office and/or certain other foreign jurisdictions.  
All other terms and product names may be trademarks or registered trademarks of their respective owners, and are hereby  
acknowledged.  
Pantone, Inc. is the copyright owner of color data and/or software which are licensed to Electronics for Imaging, Inc., to distribute  
for use only in combination with the products, or software of Electronics for Imaging, Inc. PANTONE Color Data and/or Software  
shall not be copied onto another disk or into memory except as part of the delivery of the Electronics for Imaging, Inc., products  
or software.  
Oki Data Americas, Inc., 2000 Bishops Gate Blvd., Mt. Laurel, NJ 08054-4620  
Tel: 1-800-654-3282 (856) 235-2600 Fax: (856) 222-5320 http://my.okidata.com  
© 2005 Oki Data Americas, Inc.  
59376001  
 

Miele Vacuum Cleaner S 2001 User Manual
National Instruments Network Card NI 9229 User Manual
NEC Cordless Telephone 1093092 User Manual
NEC Flat Panel Television P42XP10 BK User Manual
Nikon Camera Accessories WC E68 User Manual
Nikon Digital Camera 26431 User Manual
Nikon Photo Scanner SB3H0150010130 6MRA0830 User Manual
Nikon Switch KT 10FV2 User Manual
Optimus Portable Speaker AMX 4 User Manual
Panasonic Electric Shaver ES2235 User Manual